Seafoam is nothing but such type of service, which is a fuel additive in increasing the performance of the vehicles. The very important use of it is to clean your fuel and oil system off deposits. Carbon, which produces in the combustion chamber, causes to reduce the efficiency of the engine.
To increase the efficiency of the engine, we need to remove carbon from the combustion chamber. One way of cleaning this carbon is by using seafoam. It helps in reducing the emission by cleaning the carbon from the chamber and increase the performance of the vehicle.
Fuel and oil continuously use in the vehicle and cause in producing the sludge deposits in the combustion chamber. Seafoam can be added into the gas tank when you are refilling your tank or can also be added into the oil filter when you do car service.
It is such a liquid whose work is only the decomposition of the carbon without interfering with the fuel or oil. It helps in lubricating the moving parts of the fuel system. In the fuel system, to increase the fuel ignition, seafoam absorbs water.
How to use seafoam
Seafoam gives many benefits when used in lubricating the moving parts. This can be used in the engine, oil system, and fuel injectors. It is very important to know how much amount of this seafoam can be added in the system to produce an effective outcome.
If the amount of seafoam is increases in the engine, then it will cause in creating more problems and reducing efficiency. There are three main uses of the seafoam, which are discussed in detail below.
In the fuel:
One bottle of this seafoam can treat up to 16 gallons or 60.6 liters of fuel. This seafoam does many functions in the fuel tank. It removes deposits from the fuel and makes it more effective. It controls the moisture in the fuel and causes in increasing the fuel ignition.
In the case of diesel, it acts as a de-icing agent. The reason is that it has an anti-gel property. Through this, it purifies the diesel form the deposits and makes it perfect for the engine.
We use half of the bottle to perform this instead of a full bottle. Because the number of seafoam increases, then it will cause in damaging the engine and decrease its performance.
When you are fueling your car, then make sure to leave some space for the seafoam. It is good that you use the seafoam, which has octane level 91 or more, because it will interact with the fuel and clean the fuel injectors.
In the crankcase:
To quiet down the noisy oil filter or cleaning the oil and engine sludge, you have to use seafoam. You should use this seafoam 500-1000 miles or 800-1600km before the oil change, and after changing the new oil, you can apply this method again.
To use this method, you just need to pop up the cover of the oil filter, and by using the funnel, you can add this seafoam to get the best outcome. We use about half of the bottle to use it on a safe side and can be seen two times to get good performance.
Read Also: Best Car Wash Mop Review
In the top end:
To clean the combustion chamber and intake system, you need to high-quality seafoam so that better output can be obtained. Some of the local seafoam does not have an aerosol spray in it so that they not able to clean the deposits as they should do.
In the top end, the seafoam should be in an aerosol spray form instead of liquid form. Firstly, you just need to start the vehicle and let your vehicle war up with the minimum revolution of 2000 rpm after this pour this spry into the engine and turn off the vehicle.
After giving some rest for almost 15-20 minutes, start your vehicle and drive it only for the short distances normally 8-16km until the smoke clear so that it takes maximum time to clean the engine properly.
When you are using the seafoam, they make sure that you park the vehicle in neutral manual transmission and parking mode for the automatic transmission. So that the gears properly clean from the deposits.
It is good that you park your vehicle in a well-ventilated area and let the fumes in the open air. You need to find the vacuum line that is evenly distributed into all cylinders of the fuel. Mostly brake booster is used due to satisfy the condition mention above.
Read Also: Best Jump Starter With Air Compressor Review
When you use seafoam
The fuel of the car must be clean; it should not include any impurities and should not be contaminated. The reason for these is the carbon deposits that create in the engine of the vehicle. These deposits cause in decreasing the efficiency of the vehicle.
Seafoam’s are very important for the car. If the carbon does not remove from the surface, it will cause high fuel consumption and a reduction in performance.
There are many ways by which we can determine that when is the time for using the seafoam. Some of them are discussed below:
If you have a problem in the accelerating means that you observe that there is a loss in the rpm of the vehicle, then you should know that this is due to the fuel contaminated. This contaminated fuel caused by the bad performance of the vehicle.
Due to this, black smoke come out of the exhaust because these contaminated fuels never burn and cause in making carbon sludge deposits in the combustion chamber of the vehicle.
The color of the fuel is very important in determining the deposits of carbon or any impurities. The color of the fuel should be very clear and bright. If the color is black and dusty, then you should know that the fuel is contaminated.
There are many causes from which the color of the fuel become black and cause in decreasing the performance of the vehicle. To improve efficiency, you need to determine the exact cause of the problem.
Seafoam is one of the best solutions to such problems. In this, we add seafoam, and then all the carbon deposits, which play an important role in decreasing the efficiency, will be removed.
The leaked fuel tank of vehicle:
The fuel tank of the car is well hidden in the car and not directly affected by the outside weather. With the passage of the time, the sludge of carbon collects in the surface of the tank and causes in leaking the fuel.
The sludge which is formed is due to the bad filtration process. Due to the hole in the cylinder, all the dust forms the surrounding enter in the cylinder and cause in forming deposits.
One of the most common cause is not tightly close the lid of the tank. Because in many cases, drivers forget to close it properly, and all the dust enters the cylinder.
Read Also:10 Best Truck Bed Bike Rack
Seafoam in storing fuel:
There are three basic steps by following those steps we will be able to store fuel properly for a long time. These three steps are discussed below:
To prevent the fuel from evaporating and the formation of the blocks, we use the method of seafoam motor treatment. These blocks and varnishes are the major cause in making the efficiency of the engine poor.
If this is exposed to the open air, then it evaporates, and due to the presence of oxygen, the freshness of the fuel also decreases. To store fuel up to one or two years, you must add seafoam.
In storing the high concentration of the petroleum to protect it from the outside moisture and to dray out, we use the spray of the seafoam.
These sprays protect the surface and cause in making the surface corrosion proof. To apply seafoam, we use carburetor throats.
When we store cylinders, then we need to use deep creep to prevent it from evaporation and covering the metal surfaces. We need to spray into the cylinder cavity and prevent the piston from petroleum.
In the end, all the things you should need to know about how to use seafoam are discussed in this article. You just need to read it carefully.
Seafoam is the best way to remove carbon deposits and in increasing the efficiency of the vehicle. You just need to pour your seafoam liquid into the fuel tank, and then it will automatically remove all the deposits and clean the surface.
The seafoam can also be used to prevent the fuel surface from being evaporating and cause an increase in the performance of the vehicle. If the seafoam is combined with the other fuel treatment, then it will not affect it.
The reason for this is that the hydrocarbons of the fuel are the same as the hydrocarbon of the seafoam. So, they don’t affect the performance of the other.